Aermet 100, Strip,UNS K92580,E FORU

British Specs:，American Specs:AMS 6532 Bar and Forgings，German Specs:

### **Product Datasheet: Aermet® 100 Strip (UNS K92580)** --- #### **1. Product Overview** Aermet® 100 Strip is the precision cold-rolled form of this ultra-high-strength secondary hardening steel, supplied in thin, narrow coils or straight lengths. This product form combines the exceptional strength-toughness relationship of Aermet 100 alloy with the dimensional precision and surface quality required for high-volume manufacturing. The strip product enables production of small, complex components where consistent material properties and tight tolerances are critical for performance and reliability. --- #### **2. Chemical Composition (Weight %)** | Element | Min (%) | Max (%) | Balance | |---------|----------|----------|---------| | Iron (Fe) | - | - | Balance | | Nickel (Ni) | 11.00 | 12.50 | - | | Cobalt (Co) | 13.00 | 14.00 | - | | Chromium (Cr) | 3.00 | 3.40 | - | | Molybdenum (Mo)| 1.20 | 1.40 | - | | Carbon (C) | 0.21 | 0.25 | - | | Manganese (Mn) | - | 0.10 | - | | Silicon (Si) | - | 0.10 | - | | Phosphorus (P) | - | 0.005 | - | | Sulfur (S) | - | 0.005 | - | --- #### **3. Physical & Mechanical Properties** **A. Mechanical Properties (After Final Heat Treatment)** - **Tensile Strength:** 1,795-1,930 MPa (260-280 ksi) - **Yield Strength (0.2% Offset):** 1,655-1,795 MPa (240-260 ksi) - **Elongation in 2 inches:** 8-12% - **Hardness:** 50-54 HRC - **Fracture Toughness:** Maintains excellent toughness in thin sections - **Fatigue Strength:** Superior performance in high-cycle applications **B. Physical Properties** - **Density:** 7.86 g/cm³ (0.284 lb/in³) - **Modulus of Elasticity:** 200 GPa (29×10⁶ psi) - **Poisson's Ratio:** 0.30 - **Thermal Conductivity:** 25 W/m·K (70°F) - **Electrical Resistivity:** 0.40 μΩ·m - **Magnetic Permeability:** Ferromagnetic **C. Standard Strip Specifications** - **Thickness Range:** 0.05-3.0 mm (0.002-0.118 inches) - **Width Range:** 10-300 mm (0.4-12 inches) - **Coil Dimensions:** ID 510 mm (20 inches), OD up to 1,500 mm (59 inches) - **Thickness Tolerance:** ±0.005 mm for precision grades - **Surface Finish:** Bright annealed or skin passed available --- #### **4. Product Applications** **Precision Components** - Aircraft fastener systems - Spring components for aerospace - Shim stock for critical assemblies - Retaining rings and clips - Precision washers and spacers **Electronics & Defense** - Connector components - Relay and switch parts - Armor piercing core material - Weapon system small parts - Guidance system components **Industrial Applications** - High-strength springs - Wear-resistant components - Cutting tool stock - Medical instrument components - High-performance bearing components --- #### **5. International Standards & Specifications** | Standard Body | Specification Number | Title | |---------------|----------------------|-------| | AMS | 6532 | Steel Bars, Forgings, and Rings (Applicable) | | UNS | K92580 | Unified Numbering System | | ASTM | A693 | Precipitation-Hardening Stainless Steel | | MIL | MIL-DTL-32375 | Detail Specification for Steel | | AS | 7482 | Consumable Electrode Melted Material | --- #### **6. Processing Guidelines** **Heat Treatment Cycle** 1. **Solution Treatment:** 900°C ± 8°C (1650°F) for 15-30 minutes 2. **Rapid Quenching:** Oil or forced air 3. **Aging Treatment:** 480°C ± 3°C (900°F) for 3-4 hours 4. **Controlled Cooling:** To room temperature **Fabrication Characteristics** - **Blankability:** Excellent in annealed condition - **Formability:** Good for moderate deformation - **Punching:** Clean edges with proper die clearance - **Heat Treatment Response:** Consistent and predictable - **Surface Hardening:** Not required due to through-hardening capability --- #### **7. Quality Assurance** - **Dimensional Control:** Laser scanning for width and thickness - **Surface Quality:** 100% visual inspection available - **Mechanical Testing:** Statistical process control maintained - **Chemical Analysis:** Ladle and product analysis certified - **Microcleanliness:** Stringent inclusion rating control --- #### **8. Special Features** - **Uniform Properties:** Consistent across entire coil length - **Premium Surface Quality:** Suitable for precision stamping - **Tight Tolerances:** Maintained through advanced rolling technology - **Batch Consistency:** Guaranteed through statistical process control - **Technical Support:** Application engineering assistance available --- **Notes:** - Material supplied in annealed condition (HRC 28-32) for forming - Protective packaging mandatory to prevent surface damage - Custom slitting and cutting services available - Consult technical team for specific application requirements **Contact Information:** [Your Company Information] *All values are typical and may vary based on specific manufacturing processes and heat treatment parameters. Refer to official material data sheets for definitive specifications.*

Packing of Standard Packing: Typical bulk packaging includes palletized plastic 5 gallon/25 kg. pails, fiber and steel drums to 1 ton super sacks in full container (FCL) or truck load (T/L) quantities. Research and sample quantities and hygroscopic, oxidizing or other air sensitive materials may be packaged under argon or vacuum. Solutions are packaged in polypropylene, plastic or glass jars up to palletized 2567 gallon liquid totes Special package is available on request.